PRODUCT DESCRIPTION:
Monochem 200: is a unique two component water borne epoxy resin. It has been modified with a special activators which are reinforced with non toxic color stable and weather resistant pigments. It is formulated to have out standing adhesion while demonstrating high resistance to chemicals,water and impact.
Monochem 200 doesn't contain toxic fumes or solvants. It is recommeded as and interior all purpose, user friendly, Architectural, industrial/Residential, insitutionl and transportation maintance coating.
Monochem 200 is for interior use only. It is not UV Stable and should not be exposed to direct sunlight.
It is recommended as an interior all purpose, user-friendly, architectural, industrial/residential,
institutional and transportation maintenance coating can be applied on concrete and masonry, metal (plain or galvanized) and wood. Common applications include machinery rooms,warehouses, factories, auto repair and residential garage floors It has ZERO VOC. It conforms to the U.S.D.A. requirements
for coatings in contact with food.
It is two-components with a 1:1 Mixing volume ratio. It is
packaged in a clear base or white base. It may be tinted with universal colorants
to match any color. is available in gloss or low-gloss
PREPARATION:
surface preparation is critical to product performance.
Surfaces to be coated must be dry and clean, free from all dirt, dust, oil,
grease, wax and loose materials or contaminants.
Bare concrete surfaces must be fully cured, porous, structurally sound, and
free from rock pockets, voids and cracks.
Dense (non-porous) concrete should be primed with,Monopole 2121
sandblasted, shot blasted, or acid etched (2-3 times) to achieve a 120 grit
feel for proper penetration and adhesion
•Remove all loose, peeling or poorly bonded paint.
•Surfaces must be mechanically abraded using 60-80 grit sandpaper.
•Clean surfaces by using a solution of ½cupTSP to one gallon of warm water. Pay special attention to areas where build-ups of dirt, grease and oil exist. These areas should be
scrubbed clean
•Dull glossy surfaces by sanding or by using a chemical deglosser.
APPLICATION REDUCTION AND CLEAN UP:
Mix at a 1:1 ratio: 1-gallon of Part A to 1-gallon of Part B. Stir Part B well before
adding to Part A. Mix with a low speed mixer for 2-5 minutes or with a stir stick
for 5-10 minutes, scraping the bottom and sides of the container. Mix only an
amount of material that can be used within a 3-hour period. Mixed material
must be discarded after 3 hours.
Monochem 200 is for interior use only. It is not UV Stable and should not be exposed to direct sunlight. At 77 F will dry in 3 hours. Wait approximately 24 to 48
hours for light foot traffic use, 72 to 96 hours for heavy foot traffic, and 5 days for
vehicle exposure. Full cure requires 14-days.
Deep or dark colors made from a clear base should always be used with a
pigmented primer or when applying over drastic color changes.
Clean tools and equipment with soap and water immediately after use. Dried
material will require a strong solvent, paint thinner or stripper to remove.
is useable for a 12-month period stored at roomtemperature (72°F) in a sealed container.
All Monopole floor coatings exposed to water, oil, grease, or any liquids may
create a slippery surface. Monopole Inc. will not be responsible for injury
caused in a slip or fall situation. It is the end users responsibility to determine
the suitability and safety of our coatings for their particular use and application.
•Do not apply over poorly-bonded paint.
•Do not apply if moisture in the substrate is higher than 15%.
•Do not apply to a surface exhibiting hydrostatic pressure.
•Do not apply if surface temperature is over 90°F. or below 55°F.
•Do not apply if surface pH level is above 8.
•Do not spread the coating too thin over an entire area and allow it to dry hard
before applying a 2nd coat is applied at the approximate spread rate of 250-300
square feet per gallon, yielding 2-3 dry mils of thickness per coat.
Two coats are required. Additional coats may be required, depending on
intended use, surface porosity and texture.
apply the second coat 2-4 hours (not to exceed 24 hours) after the first coat,
while the first coat is still tacky.
Silica sand #30 or #60 may be added or broadcast to create a non-skid finish.
is applied at the approximate spread rate of
square feet per gallon,
Two coats are required. Apply a medium to heavy first coat then allow a two
minute setup time before back rolling all rundowns in the same section. Allow
2-4 hours dry time before applying a second coat.
.
Monochem 200 is available in a clear base and white base that can be tinted
with Universal Colorants. Tint only Part A; Part B cannot be tinted. The Part A is short-filled:
ADDITITONAL DATA:
MONOCHEM 200 qualifies for earning LEED® credits for
Indoor Environmental Quality, EQ 4.2 Low-Emitting Materials,
based on low contribution of VOC.
ALWAYS apply a test patch to check for coverage rates, adhesion,
compatibility and for desired results. Responsibility for determining the
adhesion and coverage of to an existing finish rests with
the applicator. Applying over existing and poorly adhering
painted surfaces may result in the eventual lifting of the old paint
CHEMICAL RESISTANCE OF MONOCHEM 200 PER ASTM D 1308 24
HOUR EXPOSURE
Gasoline.........................................................................No Effect
Motor Fluid......................................................................No Effect
Transmission Fluid............................................................No Effect
Mineral Spirit...................................................................No Effect
Brake Fluid...............................................Slight Softening, Film Recover
Skydrol LD4..............................................Slight Softening, Film Recover
10% HCL ........................................................................No Effect
10% Nitric.......................................................................No Effect
28% Sodium Hydroxide......................................................No Effect
10% Sulphuric Acid...........................................................No Effect
10% Hydrochloric Acid.......................................................No Effect
10% Acetic Acid...............................................................No Effect
2% Aqueous Pine Sol........................................................No Effect
40% Cleaner Concentrate..................................................No Effect
DI Water.........................................................................No Effect
Urine..............................................................................No Effect
Coffee............................................................................No Effect
Vegetable Oil..................................................................No Effect
5% Tide.........................................................................No Effect
MSDS's are available upon request.
For Product delivery greater than 60 miles from the San Fernando Valley California please contact us for shipping information
You can also visit our library of references and helpful tips at our wood finishing Blog at:
www.woodfinishings.wordpress.com
